UNS N08925, UNS N08354, and UNS N08926 Seamless Pipe and Tube as standard B677 | |||||||||||||||
Standard Specification for UNS N08925, UNS N08354, and UNS N08926 Seamless Pipe and Tube This standard is issued under the fixed designation B677; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval. |
|||||||||||||||
Scope | |||||||||||||||
This specification covers UNS N08925, UNS N08354, and UNS N089262 seamless, cold-worked or hot-finished pipe and tube intended for general corrosive service. ASTM International has adopted definitions whereby some grades, such as UNS N08904 previously in this specification, were recognized as stainless steels, because those grades have iron as the largest element by mass percent. Such grades are under the oversight of ASTM Committee A01 and its subcommittees. The products of N08904 previously covered in this specification are now covered by Specifications A269 and A312/A312M. The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use. |
|||||||||||||||
Chemical Requirements | |||||||||||||||
Element | UNS N08925 | UNS N08926 | UNS N08354 | ||||||||||||
Carbon, max | 0.020 | 0.020 | 0.030 | ||||||||||||
Manganese, max | 1.0 | 2.00 | 1.00 | ||||||||||||
Phosphorus, max | 0.045 | 0.03 | 0.030 | ||||||||||||
Sulfur, max | 0.030 | 0.01 | 0.010 | ||||||||||||
Silicon, max | 0.50 | 0.5 | 1.00 | ||||||||||||
Nickel | 24.0 to 26.0 | 24.00 to 26.00 | 22.0 to 24..0 | ||||||||||||
Chromium | 19.0 to 21.0 | 19.00 to 21.00 | 34.0 to 36.0 | ||||||||||||
Molybdenum | 6.0 to 7.0 | 6.0 to 7.0 | 7.0 to 8.0 | ||||||||||||
Copper | 0.8 to 1.5 | 0.5 to 1.5 | … | ||||||||||||
Nitrogen | 0.1 to 0.2 | 0.15 to 0.25 | 0.17 to 0.24 | ||||||||||||
Iron | balance | balance | balance | ||||||||||||
The material shall conform to the requirements as to chemical composition prescribed. One test is required for each lot as defined in Specification B829. If a product (check) analysis is performed by the purchaser, the material shall conform to the product (check) analysis variations per Specification B829. |
|||||||||||||||
Materials and Manufacture | |||||||||||||||
The material shall be supplied in the solution-treated condition. NOTE 1—The recommended heat treatment shall consist of heating to a temperature of 2010 to 2100°F (1100 to 1150°C) for UNS N08925 and UNS N08926, followed by quenching in water or rapid cooling by other means. |
|||||||||||||||
Mechanical Properties and Other Requirements | |||||||||||||||
Mechanical Properties—The material shall conform to the mechanical properties prescribed. One test is required for each lot as defined in Specification B829. Nondestructive Tests: Each pipe and tube shall be subjected to either a hydrostatic test or a nondestructive electric test as described in Specification B829. The purchaser may specify which test is to be used. Hydrostatic Test: The fiber stress for the purpose of calculating the hydrostatic test pressure shall be 20 000 psi (138 Mpa). |
|||||||||||||||
Alloy | Temper | Tensile Strength, min, ksi (MPa) | Yield Strength, 0.2 % offset, min, ksi† (MPa) | Elongation in 2 in. or 50 mm (or 4D), min, % | |||||||||||
UNS N08925 | solution annealed | 87 (600) | 43 (300) | 40 | |||||||||||
UNS N08354 | solution annealed | 93 (640) | 43 (295) | 40 | |||||||||||
UNS N08926 | solution annealed | 94 (650) | 43 (295) | 35 | |||||||||||
Dimensions and Permissible Variations | |||||||||||||||
The permissible variations in dimensions set forth in Specification B829 shall apply. |
Email: info@tapgroup.vn |
Skype: info@tapgroup.vn |
Hotline/ Zalo/ Wechat: 0933 86 77 86 |
Email: purchasing03-@tapgroup.vn |
Skype: purchasing03-@tapgroup.vn |
Hotline/ Zalo/ Wechat: 0964413291 |
Email: sale01@tapgroup.vn |
Skype: sale01@tapgroup.vn |
Hotline/ Zalo/ Wechat: 0964697066 |
Email: purchasing01-@tapgroup.vn |
Skype: purchasing01-@tapgroup.vn |
Hotline/ Zalo/ Wechat: 0964697066 |
Email: sale04@tapgroup.vn |
Skype: sale04@tapgroup.vn |
Hotline/ Zalo/ Wechat: 0964697067 |
TAP - HÀ NỘI
Chi nhánh Hà Nội
Address : Số 32 Lô N4D, đường X2A, Yên Sở, Hoàng Mai, Hà Nội
Phone : 0933 86 77 86 - Email : info@tapgroup.vn
TAP - HỒ CHÍ MINH
Chi nhánh Hồ Chí Minh
Address : 137 Quốc lộ 1A, Phường Bình Hưng Hòa Quận Bình Tân, Thành Phố Hồ Chí Minh
Phone : 0933 86 77 86 - Email : info@tapgroup.vn